New Model Arrived

Electronic Counters with Large DisplaysG95 Series

6 digits
LED display
Add/Subtract
External power supply
Extra-large display

Features	New model G95-305 has joined G95 series lineup G95-305 performs RS-485 serial communication with PC/PLC (Connecting G95-305 with PC/PLC requires RS-485 serial communication device, which is in the marketplace but is not included in scope of supply.) Supplied remote controller can change several settings 101.6 mm figure height, Extra-large Electronic Counter/Display Increase progress transparency in every area/cell Increase progress transparency of the entire factory/production line Hanging/Mounting brackets accompanied

Features

New model G95-305 has joined G95 series lineup
G95-305 performs RS-485 serial communication with PC/PLC
(Connecting G95-305 with PC/PLC requires RS-485 serial communication device, which is in the marketplace but is not included in scope of supply.)
Supplied remote controller can change several settings
101.6 mm figure height, Extra-large Electronic Counter/Display
Increase progress transparency in every area/cell
Increase progress transparency of the entire factory/production line
Hanging/Mounting brackets accompanied

Movie

Models

Models	Digits	Function	Settings	Write (Setting of initial value at resetting)	Interactive Communication	Approx. Weight
G95-301	6	Totalizer	DIP switch	–	–	3kg
G95-303		Totalizer + Display (Selectable)	DIP switch	BCD Input	–
G95-305		Totalizer + Display (Selectable)	Supplied Remote Controller	RS485 or Supplied Remote Controller	RS485

Specifications

Models	G95-301 / G95-303 / G95-305
Display	RED LED Zero Suppressing : 101.6(H) mm x 60.0(W) mm
No.of Digits	6
Power	AC100 – 240V / -15% – +10% 50/60Hz
Power Consumption	Approximately 6VA
Input	Non-contact Input : Open Collector Transistor : L < 2V (Sink Current 7mA) Voltage Input : L : 0 – 5V H : 10 – 30V (Input Impedance 1.6KΩ) Contact Input : Relay, Microswitch, etc. (Sink Current 10mA)
Connection	Input : Terminal Screw Power : Terminal Screw BCD * : 25-Pin D-Sub (DB25) Connector
Decimal Point	Selectable through DIP Switch (0.0/0.00/0.000)
Maximum Count Speed	Non-contact : 1kHz Contact : 20Hz
Count Mode	90°Quadrature Input Add/Subtract (Individual)
Pulse Width	Non-contact Input : 500µsec min. Contact Input : 25msec min. (Duty 1:1)
Count Range	-99999 – +999999
Display Range ***	0 – 999999
Write Range***	-99999 – +999999 (When using negative (-) sign, Set SW5 of the DIP switch to ON.*)
Power Source for Sensor	DC12V 100mA
Reset	External Reset : 100msec min. / L < 2V (Sink Current 10mA) Power Reset & Push Button No power reset or push button reset
Input Inhibit	Input Inhibit : L < 2V (Sink Current 10mA)
Memory	E²PROM Data Retention : Approx. 10 years Memory Frequency : 100,000 times maximum
Error Display	In 90°Quadrature mode, error message will be displayed if the count range is exceeded (overflow error : o-Er underflow error : u-Er)
BCD Input *	Open Collector Transistor : L < 2V (Sink Current 60µA) or Contact Input (Digital Switch) Parallel BCD (Positive Logic / Negative Logic)
Ambient Humid. : Operating	45 – 85%RH (Non-Condensing)
Ambient Temp. : Operating	-10 – +50°C (Should not be frozen)
Ambient Temp. : Storage	-20 – +60°C (Should not be frozen)
Altitude	2,000m max.
Installation Environment	Over-voltage category II , Pollution degree 2 (IEC61010-1)
Withstand Voltage	AC1500V 1minute
Insulation Resistance	100MΩ minimum (DC500V Megger)
Noise Immunity	Square Wave Noise from Noise Simulator Power Terminals : ±2.0kV / Input Terminals : ±500V
Casing	Metal Case with Plastic Joints
Case Coating	Anodized Black
Compliance	CE, RoHS
Communication **	RS485 Serial communication
Way of Communication **	Half duplex, Asynchronous
Network **	Multidrop
Baud Rate **	9600 bps (Fixed)
Format **	ASCII code, Start bit : 1 bit, Data bit : 8 bit (Parity bit : 1 bit), Stop bit : 1 bit
Parity **	NON / ODD / EVEN (Selection)
Delay Time **	2ms (Fixed)
Communication setting method **	Infrared Remote Controller (Accessory)
Easy Software for G90-G95 **	The software can be downloaded from our website free of charge. The device should be connected to the terminal of the PC using an RS485 serial communication device available in the market.